RC-100B Remote Control for Bioloid

RC-100B Remote Control for Bioloid

RC-100B Remote Control for Bioloid
Robotis | A-000000-00327
58.57 €
20 perc. French VAT inc.

Including €0.01 for ecotax

Need a remote to control your Robotis robotics kit? The RC-100B Remote Control offers you up to 1,023 different command combinations and 3 different communication protocols!
Quantity
1 Available

Get it in 24/48h! (see T&C)

Size Chart
x
Size Chart
Payment methods (see T&C)
Debit card
PayPal
Payment by invoice
Wire transfer

With its 10 programmable buttons (plus 1 power/mode button) and various communication protocols, the RC-100B Remote Control is a true conductor’s baton for your Bioloid programmable robot. It offers up to 1,023 different possible command combinations, from the simplest of movements to the most complex sequences – your robot will have no choice but to toe the line!

To turn the RC-100B wireless remote control for Bioloid on, press the power/mode button. The led flickers twice. To turn it off, press the power/mode button during more than one second.

Each time a button is pressed or released, a communication packet is sent, containing the sum of the values of all pressed buttons. These values are powers of 2, so each combination of pressed buttons gives a different sum.

The code of the buttons for the RC-100B wireless remote control for Bioloid

The RC-100B Remote Control is also an energy-efficient device (0.07 W) that requires just 2 alkaline AA batteries to do its job. Lightweight and easy to handle, it looks a little like the famous PlayStation Controller. Equipped with a blue status LED and a slightly transparent packaging through which the internal circuitry can be glimpsed, the RC-100B is as pleasant to look at as it is in the hands!

Compatibility of the RC-100B Remote Control

The RC-100B Remote Control is designed especially for controlling all your Bioloid robot kit from a distance. It’s a wireless remote control, so your Bioloiod programmable robot must also be equipped with a wireless receiver module.

There are 3 communication protocols, for transforming your RC-100B into a ZigBee remote control, an IR robot remote control or a Bluetooth robot remote control.

NOTE: the remote’s IR function is not compatible with the built-in AX-S1 sensor.

You can see below the LED status depending on which module has been installed onto the RC-100B remote control.

Modules compatibles avec la télécommande RC-100B

Technical specifications of the RC-100B Remote Control

  • Operating voltage: 3 Vdc
  • Consumption: 0.07 W
  • Battery: alkaline LR6 AA x 2 (not included)
  • Buttons: 11 (including 1 power/mode button)
  • Programmable buttons: 10
  • Possible combinations: up to 1,023
  • Communication protocols: IR, ZigBee, Bluetooth (wireless modules not supplied)
  • Compatible wireless modules: ZIG-100, ZIG-110, ZIG-110A, BT-110A, BT-100A + BT-210, OIR-10 IR receiver
  • Weight: 80 g
  • Dimensions: 138 x 105 x 36 mm

Infrared communication using the RC-100B wireless remote control for Bioloid

Infrared communication with the RC-100B wireless remote control for Bioloid

Infrared is the default communication mode of the RC-100B wireless remote control for Bioloid. There is no need to add a emission board and the led lights up red.

But your mobile robot must be equipped with a OIR-10 infrared receiver (compatible with CM-100, CM-510, CM-530 and CM-700 Bioloid controllers).

You can configure the infrared communication channel of the RC-100B wireless remote control for Bioloid between 1 and 8. For this you have to press simultaneously on the power button and on the button corresponding to the channel you wish.

configuring the infrared channel of the RC-100B wireless remote control for Bioloid

To check the current channel, simultaneously press the two upper buttons, the number of flickers corresponds to the number of the channel.

The receiver must of course be configured on the same canal (configurable in the program of the controller).

Zigbee communication with the RC-100B wireless remote control for Bioloid

the RC-100B wireless remote control for Bioloid can communicate through zigbee using a zig-110A module

The RC-100B wireless remote control for Bioloid can be associated to a Zig100 set (CM-5 controller) or Zig-110A set (CM-510, CM-530CM-700 and CM-900 controllers) to communicate using the zigbee technology. The led becomes blue.

For this, you have to mount the zig-100 board in the position named 'bt-110/zig-100' at the bottom of the RC-100B wireless remote control for Bioloid.

Emplacement de la carte zig-110 ou bt-100 sur la télécommande sans fil RC-100B pour Bioloid

Push the board until the area circled red on the picture are on contact.

emplacement du module zig-110 ou bt-100 dans la télécommande sans fil RC-100B pour bioloid

If, after a vibration for example, the contact is lost, the RC-100B wireless remote control for Bioloid will go back to infrared communication automatically.

If you wish to use your Zig100 or Zig-110A module in broadcast mode, you can chose the channel (1 to 4) by pressing simultaneously the power button and one of the number buttons. Communication may be interrupted a few seconds while channel is changed. If you change the batteries of your RC-100B wireless remote control for Bioloid, the configuration is lost.

Bluetooth communication with the RC-100B wireless remote control for Bioloid

using a BT-110A bluetooth module to communicate with the RC-100B wireless remote control for Bioloid

The RC-100B wireless remote control for Bioloid can be associated to a BT-110A set ( CM-510,CM-530, CM-700 and CM-900 controllers) to communicate using the bluetooth technology. The led becomes blue.

As for the zigbee communication, you have to mount the BT-100 board at the bottom of the RC-100B wireless remote control for Bioloid. The mounting instruction are the same. This is how it looks like one the board is mounted.

emplacement of the BT-100 board inside the RC-100B wireless remote control for Bioloid

No configuration is required.

Accessories
Customers who viewed this item also viewed