Câbles

Different types of cables for your robots or other projects. You will find here USB cables (all types), as well as cables for prototyping (jumper, Dupont...).

Active filters

A dedicated USB cable/jack to connect your Odroid boards to a USB host.

In Stock

3 pin Extension cable for servomotors, ultrasound sonar sensor Ping))), LCD screen and all 3 pin sensors. The lenght of the cable is 25,4 cm (10-inch).

3 pin Extension cable for servomotors, ultrasound sonar sensor Ping))), LCD screen and all 3 pin sensors. The lenght of the cable is 30 cm (12-inch).

In Stock

These 3 pin couplers will be very useful when converting your jumper wires into home extension wires!

In Stock

3 pin Extension cable for servomotors, ultrasound sonar sensor Ping))), LCD screen and all 3 pin sensors. The lenght of the cable is 20 cm (8-inch).

In Stock

3 pin Extension cable for servomotors, ultrasound sonar sensor Ping))), LCD screen and all 3 pin sensors. The lenght of the cable is 10 cm (4-inch).

In Stock

The 4-Pin Female Jumper to Grove 4-Pin Conversion Cable (x 5) will make it easier for you to connect your Grove modules.

In Stock

Make neatly organised circuits with these female/female 30-cm long jumper wires in various colours!

In Stock

This 5V USB to 9V jack power cable ideal for your Marty robot, but it can be used anywhere a 9V source is needed.

In Stock

This pack of thirty 3-wire extension cables by Parallax will prove extremely useful when wiring your projects, however big or complex!

In Stock

Are you looking for the best way to reconcile your Raspberry Pi or Beagle Bone with the Grove system? This Grove 4-pin/4-pin jumper conversion cable will increase your wiring possibilities.

In Stock

Make sure you always have your favourite cables to hand when prototyping! This hook-up wire spool set of 22 AWG cables in various colours will save you the hassle of looking everywhere for your breadboard cables – they’re all there, stored neatly away, just waiting to be used!

In Stock

A great jumper cable for connecting your programming board to pretty much anything!

In Stock

Simple six wire cable with a 10cm length. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers.

In Stock

This pack of 50 jumper male-male is a good start to get your prototyping starting!

In Stock

You can use this 40 jumper wires harness as it is, or you can pull the ribbon wires off to make individual jumpers, pretty cool!

In Stock

This 20 jumper wires harness is great for prototyping neatly! If you want, you can also pull the ribbon wires off to make individual jumpers.

In Stock

This 40 jumper wires harness will be quite handy for prototyping.You also have the possibility to pull the ribbon wires off to make individual jumpers.

In Stock

This pack of 40 jumper wires will come in handy for making wire harnesses or jumpering between headers on PCB's. Plus, you can also pull them off to use them individually. A must have for your prototyping projects!

In Stock

Set of 40 jumper wires with male header contacts on either end for connecting PCBs.

In Stock

A strip of 40 premium male/male jumper wires of 150 mm length for your assemblies. If you don’t want to connect them in strip, no problem, you can detach them to use them individually.

In Stock

4.5 m of 10-wire ribbon cable for neat connections!

In Stock
€2.66 €2.95 -10%

Create a nice and tidy wire harness for your multiple connections with this 4.5 m 6-wire ribbon cable.

In Stock

This set of 10 30 cm long 3-pin cables is for use with sensors, servomotors and other RobotGeek modules.

In Stock