.

Câbles Dynamixel

Thanks to these cables, you will be able to set up the necessary wiring on your Dynamixel creations: connect your robots to the different sensors and actuators, as well as their control board. The Dynamixel cables are solid and long-lasting, a must-have in your toolbox!

Active filters

10 cables (10cm lenght) with 3 pin connectors for the Dynamixel servomotors of the AX and MX-xxT series.

In Stock

10 cables (14cm lenght) with 3 pin connectors for the Dynamixel servomotors of the AX and MX-xxT series.

In Stock

10 cables (18cm lenght) with 3 pin connectors for the Dynamixel servomotors of the AX and MX-xxT series.

In Stock

10 cables (20cm lenght) with 3 pin connectors for the Dynamixel servomotors of the AX and MX-xxT series.

In Stock

10 cables (6cm lenght) with 3 pin connectors for the Dynamixel servomotors of the AX and MX-xxT series.

In Stock

10 cables (10cm lenght) with 4 pin connectors for the Dynamixel actuators of the MX (R version), RX and EX series.

In Stock

10 cables (14cm lenght) with 4 pin connectors for the Dynamixel servomotors of the DX, RX and EX series.

In Stock

10 cables (18cm lenght) with 4 pin connectors for the Dynamixel actuators of the MX (R version), RX and EX series.

In Stock

10 cables (20cm lenght) with 4 pin connectors for the Dynamixel servomotors of the DX, RX and EX series.

In Stock

10 x 24cm cables with 4 pin connectors for Dynamixel DX, RX and EX series servomotors

In Stock

10 cables (6cm lenght) with 4 pin connectors for the Dynamixel servomotors of the DX, RX and EX series.

In Stock

Pack of 10 TTL communication cables for the Dynamixel X-series servomotors.

In Stock

This set of 10 x 100 mm X3P cables is compatible with lots of the Dynamixel X servos.

In Stock

A pack of 10 X3P 18 cm cables for Dynamixel X servos.

In Stock

Flexible and strong, these 240 mm X3P cables (x10) enable a fast connection between your Dynamixel X servos and their controller.

In Stock

The X4P 100 mm cable is designed especially for connecting your Dynamixel XM-430 servos quickly and efficiently. You’ll find it hard to do without this Robotis cable!

In Stock

This pack of medium-length X4P cables for Dynamixel XM-430 offers greater flexibility in terms of wiring.

In Stock

With this pack of X4P 240 mm cables, you get 10 4-pin Dynamixel cables of the highest quality to connect your XM-430 Dynamixel servos.

In Stock

This pack of ten 180 mm X4P cables (convertible) is to be used with Dynamixel X-series servo motors with an RS485 interface.

In Stock

35cm long cable for Dynamixel X-series servo motors, TTL protocol.

In Stock

Dynamixel X-series compatible cable (TTL), length 50 cm.

In Stock

This 3P Cable Set for Dynamixel servo motors in the AX and MX series lets you make all the standard connections between your robot and the various sensors and actuators that it needs.

In Stock

Use this pack of five 3P-Sync 160 mm cables for connecting two Dynamixel MX-106 and X540 servos in master/slave mode.

In Stock

These 4 x 120 mm 4P cables (for wireless module) are intended exclusively for connecting your Dynamixel servo motors using the RS485 protocol.

In Stock