.

Connectivité et accessoires pour Arduino

Batteries, relays, adapters... all accessories to complete your Arduino-based electronical circuits.

Active filters

Sensors, sensors, and yet more sensors! With the SEN-12799 Essential Sensor Kit, you’ll be able to explore all the possibilities offered by these various detection and measurement devices. Over to you now!

In Stock

The 5 x 10 cm Heating Pad by SparkFun is an accessory that can be very easily connected and integrated into creations to help you get safely through the winter!

In Stock

This small voltage meter is ready to be embedded in your mobile robot to display the voltage you will put on its cables, for example the battery voltage.

In Stock

Compact and yet highly effective, the MAX98306 Stereo 3.7W Class D Audio Amplifier is the perfect device for your portable audio creations on Arduino!

In Stock
€5.54

The TEM01052B Load Sensor is equipped with a flexible half-bridge allowing you to measure loads of up to 50 kg.

In Stock

The Ardumoto Shield is an easy-to-use dual motor controller for Arduino board. Combined with an Arduino board, the Ardumoto makes a fantastic controller platform for small mobile autonomous robots.

In Stock
€189.90

This pH Sensor Kit includes all the essential elements needed for reliable pH measurements and saving the data collected on an Arduino board. The pH Sensor Kit is so accurate that it is ideally suited to laboratory use.

In Stock

Mechanical parts for easy Pan/Tilt setup

In Stock

This very compact charger will recharge your one cell LiPo and Li-Ion batteries very quickly. It is powered by a microUSB câble.

In Stock

This charger for one cell LiPo or LiIon batteries will easily be integrated in all you robots to allow a recharging without removing the battery, with a standard USB cable.

In Stock

The 16 GB Class 10 micro SD MB-MSAGB memory card offers you an effective way to boost your mobile or smartphone.

In Stock
€16.50

The 16x8 LED Matrix marketed by Adafruit is in reality a complete kit that includes two 8x8 LED displays and their controller driver, and which can be easily implemented and integrated into all your DIY projects!

In Stock

This 6-Pin Stackable Header for Arduino will allow you to easily connect your compatible shields on an Arduino base.

In Stock

The Assembled Pi T-Cobbler Plus with GPIO Cable is the new Adafruit extension designed especially for Raspberry Pi B+ fans who want to be able to easily use all the additional ports offered by this board.

In Stock

Clever and efficient, the Peristaltic Liquid Pump with Silicone Tubing can be integrated into numerous projects requiring a constant liquid flow without contact between the motor and the liquid.

In Stock

The instant 3-Pin SPDT Micro Switch offers 2 different connection possibilities, and can also switch to SPST mode.

In Stock

The Pololu 12 Vdc 2-Channel SPDT Relay Carrier allows you to control 2 single pole, double throw switches (SPDT). It comes already assembled.

In Stock

This OLED display module may be the size of a chip, but it will clearly display all the data you want thanks to its OLED screen. Arduino compatible, it will fit perfectly onto your board to make prototyping easy!

In Stock

With the Tiny AVR Programmer, in-system programming of ATtiny45 and ATtiny85 integrated circuits is now possible. All you need is a USB connection to be able to program a miniature Arduino project!

In Stock

The MIFARE SM130 RFID Module by SparkFun is a 28-pin DIP module that provides easy access to the 13.56 MHz RFID technology on Arduino.

In Stock

With the Uninterruptible Power Supply for Raspberry Pi, your board becomes safe and autonomous thanks to a rechargeable-battery system.

In Stock

What use would your RFID boards be without a matching module? This one is compatible with Arduino, Raspberry Pi and Intel Galileo [XBee Socket]. No more excuses for postponing your next IoT project!

DISCONTINUATED ARTICLE

Store lots of photos and Full HD+ videos using the SanDisk Extreme Pro 32 GB memory card, fast and highly resistant to day-to-day incidents.

In Stock

These headers will allow you to stack several shields on top of your Arduino R3, Leonardo and new Arduino boards going forward.

In Stock