Robotic components (frame/body)
Robotic components to make DIY robots. You will find here all the building parts to assemble your robots (or automation systems): chassis, wheels, cables, beams, screws... Everything you need to build a robust body for your robot is here.
Set of colored jumper cables with stiff ends molted on for breadboards.
This universal hub is designed to adapt to all types of Mecanum wheel.
The BNS-10 Nut and Bolt Set is a kit that will allow you to not only assemble Dynamixel AX (12+) servo motors, but also fit your mobile robot with an AX-S1 sensor and CM-5 or CM-510 controller.
The Pololu Universal Aluminium Mounting Hub Shaft allows you to attach wheels or other mechanisms to 4 mm motor shafts. It provides two mounting hubs along with two 4-40 screws and the corresponding Allen wrench to secure the hub to the motor shaft. Each mounting hub has 4 holes for 4-40 screws (not included) that can be used to attach a wheel.
This 100mm omni ball bearing wheel from Nexus Robotics allows you to design your own omnidirectional robot.
A set of 40 female-female cables of different colors for standard 0.1" (2.54mm) headers.
ServoCity is offering you this 90° angle bracket in aluminium to assemble the various mechanical, electrical or electronic parts of your robot in no time.
Universal mounting hub to adapt wheels on your mobile robots
The Pololu Ball Caster with 1/2” Metal Ball kit comes with everything you need to mount a 12.7 mm diameter caster on your robotic structure.
Bag of 25 T-slot nuts for MakerBeam made of stainless steel, 25 M3 4mm A2 bolts (ISO7380) and 25 M3 4mm A2 bolts (DIN7991). Great to fasten brackets (use the ISO7380 bolts) or corner cubes (use the DIN7991 bolts).
Check out our MakerBeam accessories range.
Compatibility: MakerBeam
Add this 50 pieces S2 PHS Bolt M2*8 kit for Dynamixel servomotors to your roboticists’ toolbox.
Are you looking for the best way to reconcile your Raspberry Pi or Beagle Bone with the Grove system? This Grove 4-pin/4-pin jumper conversion cable will increase your wiring possibilities.
This Pair of 32 x 7 mm Wheels for DIY Mobile Robots can be effortlessly adapted for use on many types of Pololu motors, including its metal gear motor model!
The 4-Pin Female Jumper to Grove 4-Pin Conversion Cable (x 5) will make it easier for you to connect your Grove modules.
Have you ever been afraid of running out of assembly parts in the middle of a project? With this set of 400 S1 Bolt PHS M2x6 for Dynamixel Servomotors , you’ll have more than enough bolts to keep going for a while !
You can use these white plastic wheels to build small mobile robots.
Make sure you choose tools truly compatible with your M2 and S1 screws and for fixing the servo horns and bearings on your servo motors with this Pack of 400 M2 nuts for Dynamixel AX-series servo motors!
USB Type-A to mini B cable: the most practical for lightweight devices
3 pin Extension cable for servomotors, ultrasound sonar sensor Ping))), LCD screen and all 3 pin sensors. The lenght of the cable is 10 cm (4-inch).
The T’Rex Metal Tank is a chassis for all-terrain mobile robots designed for exploring the roughest terrain, even in wet weather. A real tank!
The Lego Mindstorms EV3 and NXT robots include a great many mechanical and electronic parts, all of them invaluable: with this Pack of 2 Ball-Bearing Mounts for Lego Mindstorms, you’ll never run short of ball-bearings again.
Simple six wire cable with a 10cm length. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers.
A very robust and resistant Pan & Tilt kit by ServoCity that supports cameras and sensors weighing up to 907 g and is compatible with all standard-sized servos.
Not sure which wheels to choose for your next mobile platform? The Pololu Aluminium Wheel Adapter for 6 mm Shaft will open up a whole new range of possibilities!