The 4P JST Expansion Board is an extension board that allows you to add additional features to your robot.
The MakerBeam T bracket can be used in all your projects based on OpenBeam and MakerBeamXL profiles.
Bag of 250 regular nuts for MakerBeam.
Check out our MakerBeam nuts and bolts.
Compatibility: MakerBeam, OpenBeam, MakerBeamXL
1 piece of 900mm clear anodised MakerBeam beams (clear). Width and height = 10mm x 10mm. You will find below a technical drawing.
Check out MakerBeam beams range.
8 pieces of 200mm black anodised MakerBeam beams (black). Width and height = 10mm x 10mm. You will find below a technical drawing.
Check out MakerBeam beams range.
One Dynamixel XM-430 servo, 3 mounting options! With the FR12-S101K set of structural components, you can mount your Robotis servo laterally.
The MX-64AR is a Dynamixel servomotor, with high-level control features and very precise. It is more powerful than the MX-28AR and features the same caracteristics than the MX-64R except for the aluminium case enabling a better heat dissipation.
Mechanical set for Dynamixel RX-24F, RX-28 and MX-28 actuators
The CM-530 main controller drives your Dynamixel servomotors AX and MX. It carries a ARM Cortex STM32F103RE microcontroller and is programmed in USB with the RoboPlus software.
SLAMTEC has introduced the RPLIDAR C1, a cost-effective and high-definition LiDAR.
4 pieces of 300mm clear anodised MakerBeam beams (clear). Width and height = 10mm x 10mm. You will find below a technical drawing.
Check out MakerBeam beams range.
Make your DJI Tello drone’s flights less risky with this propeller guard set. It will protect both your device... and anyone it might hit!
Bitcraze has created a new kit for its tiny programmable Crazyflie 2.1+ drone(ROS compatible). This time it comes with a radio amplifier and ToF sensor!
These MakerBeam L brackets allow you to design robust and durable projects based on MakerBeam or OpenBeam profiles.
The Dynamixel FR13-S102K side frame kit can be assembled on the bottom side of your Dynamixel X540 servo motor.
Bearings for MakerBeam that comes with 10 bearings, 10 M3 12mm squareheaded bolts with hex hole, 10 washers, 10 M3 nuts and 10 M3 self locking nuts. Bearing thickness: 5mm, outside dimension: 13mm, inside diameter: 3mm.
Check out our MakerBeam accessories range.
Compatibility: MakerBeam
1 piece of 600mm clear anodised MakerBeam beams (clear). Width and height = 10mm x 10mm. You will find below a technical drawing.
Check out MakerBeam beams range.
The XH430-W210-R is one of the most comprehensive servos in the Dynamixel range. This scalable servo offers endless possibilities and will become the perfect companion for mounting the most complex robotics platforms!
You can always do with a spare 9-wire analyser cable for your Saleae Logic or Logic16 logic analyser!
Pack of 6 Dynamixel MX-28AT actuators without any accessories
The MX-106R is a Dynamixel servomotor, with high-level control features and very precise. It is by far the most powerful of the Dynamixel servomotors.
10 cables (18cm lenght) with 4 pin connectors for the Dynamixel actuators of the MX (R version), RX and EX series.
Horn and bearing set for Dynamixel actuators compatible with the Dynamixel RX-64 (N101 type) and EX-106+.
Introducing the Nexus Robot 127mm Aluminum Omnidirectional Wheel, offering a perfect combination of reliability, maneuverability, and durability for your advanced robotics projects.