The Lithium-Ion 3.7 V 1300 mAh LB-041 Battery is a rechargeable battery designed especially for your Robotis-Mini (*) robot and the OpenCM9.04 microcontroller.

This compact, lightweight, energy-efficient version of the professional Dynamixel servos offers a full range of controls combined with a high resolution.

Good news for all Raspberry Pi enthusiasts: the Raspberry Pi Zero WH board offers all the features of a Pi Zero, plus an already soldered GPIO 40-pin header!

You can now power, connect and program all your Dynamixel servos, whatever the model, thanks to this official and very clever Dynamixel starter set.

The fastest actuator for positionning of the AX range

The U2D2 board from Robotis enables you to supply a variety of power sources to your Dynamixel servo motors.

With the XC330-M288-T model, Robotis is offering a programmable servo that performs ver well in terms of speed, similar to what you’ve come to expect from the servos is the XC series. And its torque is the highest in its range.

Manufacturer reference: 902-0173-000

Horn and Bearing set for Dynamixel compatible with RX-24F and RX-28 actuators.

Sabertooth 2x32 is a dual channel motor driver capable of supplying 32A to two motors–with peak currents up to 64A. It can be operated from radio control, analogue, TTL serial or USB inputs. It uses regenerative drive and will boost your robot!

This 1,800 mAh LIPO battery is the perfect choice for charging your TurtleBot 3, Robotis OP3 or DARwin-OP robot. It incorporates a PCM specially designed to protect the battery.

A power adapter for the Pixl and Arduino boards, used to control the XL-320 servomotors and power up the Raspberry Pi that made up the Poppy Ergo Jr robot (or any other robot using these servos!)

Horn and bearing set compatible with RX-64 (N101 type), EX-106+, MX-64 and MX-106 Dynamixel actuators.

An essential accessory for your DARwin-Mini robot’s Li-Ion LB-041 Battery, the LBB-041 Battery Charger is very easy to assemble and use. It is compatible with the previous LB-040 battery.

The fastest actuator for positionning of the AX range

Choose quality cables for powering your Dynamixel XL servos tailored to your projects’ needs by opting for this pack of five 3P 160 mm Cables for XL Servos.

This set of 10 FP04-F3 side mounting frames is designed for the Bioloid robotics kits by Robotis that use the AX series Dynamixel servomotors.

The MX-28AT is an improvement upon the MX-28T model. "A" stands for "Aluminium", the new aluminium body is now allowing a better heat distribution, and the MX-28AT is also equipped with a new fastening system.

The OpenCM 485 Expansion Board connects to your OpenCM9.04 Controller so you can benefit from additional Dynamixel ports.

The Raspberry Pi’s dedicated camera module has just evolved! Discover the OmniBSI technology and rediscover the thrill of high-quality images...

Looking for an efficient actuator in TTL mode? Discover the Dynamixel XM430-W350-T servo, a model of its kind in terms of performance and control!

This 100mm omni ball bearing wheel from Nexus Robotics allows you to design your own omnidirectional robot.

The BNS-10 Nut and Bolt Set is a kit that will allow you to not only assemble Dynamixel AX (12+) servo motors, but also fit your mobile robot with an AX-S1 sensor and CM-5 or CM-510 controller.

Discover the Dynamixel XM430-W210-T servo, offering versatility, full control, a high transmission rate and a TTL interface.

In this set, you’ll find 10 sturdy plastic structural components for Dynamixel AX servo motors, suitable for replacing components in Bioloid robots.