.

Communication

A robot must be able to communicate, either between its components, with other robots or remote computers. This category gathers all communication modules for your robot: standard radio protocols such as Xbee, Bluetooth, Wifi, standard wired communication module (USB, FTDI, RS232, CAN ...).

Active filters

Offering a long range and low power consumption, the XBee Pro 60 mW PCB Antenna - Series 1 by SparkFun will solve all your inter-device communication problems!

In Stock

This WRL-12571 XBee WiFi Module with Wire Antenna strikes an ideal balance between the simple software and hardware associated with the XBee modules and the Digi WiFi communication technology.

In Stock

The BlueSMIRF Gold Bluetooth Modem is an easy way to add some Bluetooth connectivity to your mobile robot

In Stock

Want to control and optimise your data rate without using UART? Get the CC3000 WiFi module and its dedicated WiFi Breakout Board and you can integrate the Internet into your projects!

In Stock

Have you plans to create a project incorporating the NFC or RFID technology? Then you’ll probably find this NFC/RFID module, based on the PN352 chip, extremely useful. The chip is already found in lots of mainstream devices using near field communication, or NFC.

In Stock

You’re going to need an RFID reader if you want to start working on non-contact ID projects, and the ID-20LA module by ID Innovations is an extremely simple one to use. Perfect for beginners!

In Stock

This Arduino-compatible miniature development board embarks a fast and efficient WiFi module and an ATSAMD21G18 processor with plenty of memory space. It is thin, light, and lets you fly!

In Stock

The MIFARE SM130 RFID Module by SparkFun is a 28-pin DIP module that provides easy access to the 13.56 MHz RFID technology on Arduino.

In Stock

The Bluno is a microcontroller designed for projects integrating the Bluetooth 4.0 technology. It combines an Arduino Uno board and a Bluetooth 4.0 module (BLE) in a single piece of hardware.

In Stock
€35.30

The BT-410 set includes a master module and a slave module for transmitting data over a Bluetooth BLE connection, for instance between a robot and an RC-100B type wireless controller.

In Stock

The BT-210 Bluetooth Module is a wireless communication module using Bluetooth technology: it allows your robot to connect with other devices fitted with a Bluetooth 2.1 interface.

In Stock

This SparkFun XBee Explorer USB Board includes a FT231X converter for programming your XBee module directly from your computer.

In Stock

The Adafruit Bluefruit Feather is a miniature development board that includes a BLE module, USB port, battery connector and enough memory to let your imagination go wild!

In Stock

Check out the new Bluetooth breakout board by SparkFun, specially designed for Bluetooth Low Energy 4.0. Compatible with Arduino and Arduino Pro, the board is equipped with the BC118 Bluetooth BLE 4.0 module.

In Stock
€25.90

A great little module for RFID fans, the RFID USB Reader will open up new possibilities for RFID-compatible scanners. Including the ability to download the information stored on an RFID card by USB!

In Stock

When connected to a robot, this Robotis Bluetooth module allows a tablet or smartphone to control the robot using the Bluetooth Low Energy (BLE) 4.0 protocol.

In Stock

The Seeed Studio BLE Shield will allow you to incorporate the Bluetooth Low Energy technology into all your low-speed data transmission projects.

In Stock

The Me Bluetooth Module v1 (dual mode) is a small Bluetooth 2.0 and 4.0 compatible module you can use on all your iOS and Android devices.

In Stock

This Wifi module connects to Raspberry Pi through USB and brings it a Wifi connection.

In Stock

The WRL-11713 WiFi Dongle is the most efficient solution for equipping your pcDuino with a WiFi connection. And, even better, it also works with Raspberry Pi and BeagleBone Black!

In Stock

With this RFID Evaluation Shield you can connect the SM130 RFID module to your Arduino without any painful welding. Things are always simpler with XBee!

In Stock

The Feather Huzzah is a small board embedding WiFi and USB connectivity options, that you can program on Arduino or with Lua. A big thank you to the Adafruit team!

In Stock