Dynamixel XL-320 mini servo motor used for small robotics projects and fast prototyping. Comes with a 5" 3-pin cable.

The Dynamixel AX-12A is the entry-level actuator from Robotis. Its low cost makes it a best seller for all non-essential mechanical functions of your robot.

With the Dynamixel XL330-M288-T servo motor, Robotis is offering an entry-level servo with the functionalities of some of its most advanced products.

The XL430-W250-T Dynamixel servo with a TTL interface falls in the family of “low cost” servo motors, but it still provides great flexibility of assembly and use, and a compact design for all your small creations.

This compact, lightweight, energy-efficient version of the professional Dynamixel servos offers a full range of controls combined with a high resolution.

The USB2AX is a small interface to control Dynamixel servomotors like the AX-12 or the MX-28T from a computer.

With its higher gear ratio and stall torque, the Dynamixel XC330-T288-T is one of the most powerful servo motors in the XC series.

Manufacturer reference: 902-0171-000

Program many Dynamixel servos directly with the U2D2 Dynamixel/PC connector, for AX/MX to pro series!

The SMPS2Dynamixel allows you to power your Dynamixel servomotors if you don't use a controller.

With the XC330-M288-T model, Robotis is offering a programmable servo that performs ver well in terms of speed, similar to what you’ve come to expect from the servos is the XC series. And its torque is the highest in its range.

Manufacturer reference: 902-0173-000

With its new version of the camera sensor, Charmed Labs offers you a smaller and faster sensor to equip your creation! With its improved software and new mode, the Pixy2 V2.1 camera sensor could become your new favorite accessory for your robots!

The U2D2 board from Robotis enables you to supply a variety of power sources to your Dynamixel servo motors.

Available exclusively at Génération Robots, the Pixl board was made for using Dynamixel XL-320 motors on a Raspberry Pi designed for the Poppy Ergo Jr educational robot. Not compatible with Raspberry Pi 3B+.

use this PCB connector to extend your constructions based on Dynamixel actuators

Horn and bearing set for Dynamixel actuators compatible with the RX-24F, RX-28 and MX-28 actuators.

The Dynamixel shield for Arduino from Robotis can be used to control yourDynamixel servo motors using your Arduino board or an OpenCR controller.

Sabertooth 2x32 is a dual channel motor driver capable of supplying 32A to two motors–with peak currents up to 64A. It can be operated from radio control, analogue, TTL serial or USB inputs. It uses regenerative drive and will boost your robot!

10 cables (20cm length) with 3 pin connectors for the Dynamixel servomotors of the AX and MX-xxT series.

Robotis has rounded out its XC330 range with some servo motors that are equally fast and fun to control. The Dynamixel XC330-T181-T servo will reach 113 rpm!

Manufacturer reference: 902-0170-000

The HN11-I101 Horn Set is the perfect fit for Dynamixel XL430 servos.

You can now power, connect and program all your Dynamixel servos, whatever the model, thanks to this official and very clever Dynamixel starter set.

The PS-10 SMPS charger allows you to power your Dynamixel controllers and servomotors.

The Turtlebot3 Burger is a mobile robotics educational platform that’s lightweight, compact, cost-effective and customisable at will. It’s the perfect solution for all those looking for a fun medium to use in their robotics programming workshops, but also for apprentice robotics engineers, and for creators and designers.

Horn for Dynamixel actuators RX-64 (N101 Type) ,EX-106+, MX-64 and MX-106