Dynamixel XH430-W210-T Servo

Dynamixel XH430-W210-T Servo

Dynamixel XH430-W210-T Servo
Robotis | A-000000-02766
440.71 €
20 perc. French VAT inc.

Including €0.01 for ecotax

The Dynamixel XH430-W210-T servo belongs to the high performance range of Robotis actuators with a TTL interface. You won’t get enough of it!

2 Available

Get it in 24/48h! (see T&C)

Size Chart
Size Chart
Payment methods (see T&C)
Debit card
Payment by invoice
Wire transfer

Dynamixel XH430-W210-T servo: 6 control modes available

First and foremost, like with all the Dynamixel servomotors from the X series, you’ll benefit from 6 exceptional control modes including trajectory, velocity, power, PWM or torque controls.

All the data can be edited from an exclusive dashboard on Linux, Mac or Windows. You can access the dashboard using a USB2Dynamixel stick or connecting a compatible Dynamixel controller.

This ultra controllable servo allows for great fluidity of movement and also has what it takes to satisfy fans of radio-controlled wheeled vehicles who will be delighted with the PWM mode.

Robotis XH430-W210-T servo: mountable at will

As if this were not enough, the Robotis XH430-W210-T servo also offers interesting mounting options. To reduce friction and keep the cables out of the way when the servo is on, you can choose between 3 wiring possibilities, including one at the back.

Dynamixel XM430-W350-T actuator

You’ll also benefit from a large range of brackets compatible with the aluminium case, resistant to overheating: whatever project you have in mind, this servo will never interfere with it.

Technical specifications of the Dynamixel 902-0127-000 actuator

  • The Dynamixel XH430-W210-T servo comes with:
  • 1x HN12-N101 horn assembly
  • 1x Teflon washer (for horn assembly)
  • 1x 180 mm X3P cable
  • 1x 180 mm X3P cable (convertible)
  • 16x Wrench Bolt M2.5*4 screw
  • 1x Wrench Bolt M2.5*6 screw
  • 10x Wrench Bolt M2*3 screw
  • 8x spacer ring
  • Specifications:
  • Weight: 82g
  • Dimensions: 28.5 × 46.5 × 34 mm
  • Reduction ratio: 212.6: 1
  • Starting torque (N.m): 2.2 @ 11.1V; 2.5 @ 12V; 3.1 @ 14.8V
  • Starting current (A): 1.2 @ 11.1V; 1.3 @ 12V; 1.5 @ 14.8V
  • No-load speed (RPM): 46 @ 11.1V; 50 @ 12V; 62 @ 14.8V
  • ST CORTEX-M3 processor (STM32F103C8 @ 72 MHz, 32 bit)
  • Absolute contactless encoder (12 bit, 360°)
  • Coreless motor
  • Resolution: 0.088° x 4,096
  • Operating range:
  • In position control mode: 360°
  • In speed control mode: endless rotation
  • Supply voltage: 10~14.8V (recommended: 12V)
  • Operating temperature: -5 to 80°C
  • Control signal: digital packets
  • Protocol: half-duplex asynchronous serial communication (8 bit, 1 stop, no parity)
  • Physical connection: TTL multi-drop bus
  • Addresses: 253 IDs (0~252)
  • Transmission rate: 9,600 bps~4.5 Mbps
  • Feedback: position, velocity, current, real-time tick, trajectory, temperature, input voltage, etc.
  • Case in metal and engineering plastic
  • Metal gears
  • Standby current: 40 mA
How to choose the right Dynamixel servomotor?

Resources for the Robotis 902-0127-000 actuator

We know you’re always hungry for more information on the Dynamixel XH430-W210-T servo, so we’ve compiled the following set of links just for you!

    My Dynamixel servomotor is not detected, what can I do about it ?

    Check that your Dynamixel servomotor is correctly configured. Do not hesitate to re-flash it with the ROBOTIS Software Roboplus. After re-flash remember to re-configure it. If the issue is not solved, contact us for an advanced support.

    My motor works but it seems like there is an offset. Why ?

    The motor is probably not well mounted. Check that you correctly mounted the horns by respecting the mark.

    My Dynamixel servomotor seems blocked. I can't turn it even when it is not alimented.

    There is probably a mechanical issue with the Dynamixel servomotor. You can directly contact us to get more advance support.

    My Dynamixel servomotor is not working properly.

    Check your power supply and the system cabling (try with a different servomotor). You can also reset the servo. If nothing works, the best solution is to go through the Dynamixel servomotor checklist!

    What is the difference between Protocol 1.0 and Protocol 2.0?

    The 1.0 protocol is dedicated to the Dynamixel AX and MX series. Protocol 2.0 is for the X and Dynamixel Pro series. Protocol 2.0 control tables include PID controls which allow for more precise adjustment of the servo motor movements. Protocol 2.0 can be updated on MX series servo motors. You can refer to the protocol 1.0 and protocol 2.0 pages for more informations.

Customers who viewed this item also viewed